Similar characteristics of SLC1 and SLC2
Operating principle	Single-line metering device with spring-loaded control piston and double-acting feed pistons
Lubricant	Plastic lubricants up to and including NLGI consistency class 2
Operating temperature	from −40 to +100 °C	from −40 to +212 °F
Systemic pressure	150–315 bar	2150–4600 psi
Relief/bleed pressure	max 68 bar	max 990 psi
Lubricant inlet connection	G3/8 or 3/8″ NPTF
Inlet fittings for tubes with an outside diameter	8, 10, 12 mm or 1/4, 3/8, 1/2 inch
Material	Steel
Corrosion resistance category (DIN EN ISO 12944)	C3
Installation position	any, preferably vertical

Differences
	SLC1		SLC2
Number of lubricant outlets	1–12		1–6
Feed volume for output/per feed stroke
It is set in advance	0,1; 0,15; 0,2; 0,25; 0,3; 0,4; 0.5; 0.6; 0.7 cm³	0,0061; 0,0091; 0,012; 0,015; 0,018; 0,024; 0.03; 0.036; 0.043 in³	0,2; 0,3; 0,4; 0,5; 0,6; 0,8; 1.0; 1.2; 1.4 cm³	0,012; 0,018; 0,024; 0,03; 0,036; 0,049; 0.06; 0.073; 0.085 in³
Regulated	0.1–0.7 cm³	0.0061–0.043 in³	0.2–1.4 cm³	0.012–0.085 in³
Lubricant outlet connection	6 mm	Outside diameter 1/4 inch	6, 8, 10, 12 mm	Outside diameter 1/4, 3/8 or 1/2 inch
Exit thread			G1/4 or 1/4″ NPTF
Dimensions	Basic version with 12 outputs		Basic version with 6 outputs
	144 × 135 × 50 mm	5.67 x 5.31 x 1.97 inches	169 × 132 × 40 mm	6.65 x 5.2 x 1.57 inches

Visual memory indicators
Operating principle	Magnetic reset indicator with red failure indicator ring and plastic protective cap
Material	Stainless steel
Operating temperature	from −20 to +70 °C	from -4 to +158 °F

Electronic parameter indicators
Operating principle	Electronic piston sensor
Material	Stainless steel
Corrosion resistance category (DIN EN ISO 12944)	C5
Operating temperature	from −40 to +85 °C (from -40 to +185 °F)
Type	3-wire DC PNP; 2-wire DC PNP/NPN
Exit function	Normally open contact
Operating voltage	10-36 VDC, cULus Class 2 power supply
Protection class	IP65
Energy consumption	max 5 mA
Compound	M12x1, four-pin connector
Standard	CE, UL, CSA, E1

Sample order
The product can be configured using a configuration code. The order template includes the applicable part number and an explanation.
SLC1G3B-1RGBBR-EXM	SLC dosing device Construction size 1 BSP thread for metric pipes Corrosion load category C3 With 4 fixed metering screws and 2 adjustment screws on top, and 6 visual indicators on the bottom Number of sections: 6, dosing volume per feeding stroke, total 11 outputs Segment 1: 0.2 cm³ (0.012 in³) (connection of outputs 2×0.1 cm³ (2×0.0061 in³) Segment 2: 0.1–0.7 cm³ (0.0061–0.043 in³) Segment 3: 0.4 cm³ (0.024 in³) Segment 4: 0.1 cm³ (0.0061 in³) Segment 5: 0.1 cm³ (0.0061 in³) Segment 6: 0.1–0.7 cm³ (0.0061–0.043 in³) Lubricant inlet connection left: straight fitting for Ø10 mm tubing, connection to EO2 Lubricant inlet connection on the right: closed Lubricant outlet connection: 11 x 6mm OD tubes, push-in type (5 x extension outlets)
You can configure your product using the CAD configurator below. This will provide you with a specific order number.

Configure the product, download the CAD file

Accessories
Part number	Description	SLC-1	SLC-2
460-706-001	Plug ø6	•	—
432-74192-1	Plug ∅1/4	•	—
223-13702-1	Plug G1/4	—	•
223-11436-1	Plug 1/4-18 NPTF		•
223-13702-2	Plug G3/8	•	•
067044	3/8 NPTF plug	•	•
454-74104-1	Spring housing for tip ∅6	•	—
554-60293-1	Spring housing, complete ∅6, insertable	•	—
454-74132-1	Spring housing for tip ∅1/4	•	—
554-60321-1	Spring housing, complete ∅1/4, insertable	•	—
454-74105-1	Spring housing, G1/4	—	•
454-74133-1	Spring housing, 1/4-18 NPTF	—	•
554-85328-1	Plastic bag with fasteners M8X70	•	—
554-85328-2	Plastic bag with fasteners M8X65	—	•
404-22614-1	Special screwdriver for metering screws	•	•

SLC dosing devices

For single-line lubrication systems