Электрический компактный насос ECP
Электрический компактный насос ECP - Image 2
Электрический компактный насос ECP - Image 3
Электрический компактный насос ECP - Image 4
Электрический компактный насос ECP - Image 5
Электрический компактный насос ECP - Image 6
Электрический компактный насос ECP - Image 7

Electric compact pump ECP

For single-line lubrication systems

The ECP pump is designed for lubricating bearings and linear guides with oil or liquid lubricant. It operates reliably in single-line systems with the ability to lubricate up to 20 points and a main pipeline length of approximately 15 meters. A built-in relief valve allows the pump to be used in SKF automatic single-line lubrication systems. The ECP pump is supplied with pre-filled cartridges or one of three plastic reservoirs of varying sizes for oil or liquid lubricant.

Regardless of the reservoir used, the ESR operates at 24 VDC and can be conveniently controlled via an external programmable logic controller (PLC). The pump also allows manual activation of the lubrication cycle. A conveniently located bleed screw ensures easy installation and startup.

Technical characteristics and advantages

  • An economical and reliable solution
  • Ease of operation
  • Extending the life of bearings and linear guides
  • Increasing operational availability
  • Accurate and reliable operation of the system
  • More lubrication points can be added to the system, given the limitations of the system design.
  • Available choice of tanks or cartridges
  • Fill level monitoring with early warning function
  • External PLC control

Application areas

  • Single-line lubrication systems
  • Lubrication of bearings and linear guides in small-sized equipment
  • Machine tool industry
  • Packaging lines
  • Equipment for the textile industry

Documentation

 Product brochure (348.0 KB)
 Installation instructions (2.4 MB)

 

Category:

Description

Filled cartridges
To eliminate the risk of lubricant contamination, SKF recommends the ECP pump version, which uses 380 ml cartridges. A cartridge version with an additional built-in fill level switch is available. The standard cartridge is pre-filled with type 00 liquid lubricant.

Advantages:

  • Minimal risk of using unsuitable or contaminated lubricant
  • Increased safety and cleaner working conditions, less lubricant spills on the floor
  • Streamlining and simplifying inventory management
  • Safe and clean cartridge replacement without removing the lid
  • By default, the cartridges are filled with liquid lubricant recommended by SKF. Other lubricants are available upon request.
Plastic tanks for easy filling
Consumers who prefer a flexible choice of reservoir sizes and easy filling choose ECP versions with transparent plastic reservoirs. To meet specific requirements, these reservoirs are available in capacities of 0.5, 1.0, or 1.7 liters. The oil reservoirs are equipped with standard fill filters. Pumps with reservoir capacities of 1.0 and 1.7 liters can be equipped with a fill level monitoring device.
ECP with 1.0 Liter reservoir for fluid grease

Advantages:

  • Working with oil or liquid lubricants
  • The tank provides flexibility and ease of filling processes
  • Tanks of various sizes are available
  • Extended service and filling intervals
  • Air removal is only necessary during system startup, not when filling the tank.
Technical specifications
Operating principle electrically driven piston pump
Lubricant
Oil
Liquid lubricant		 Viscosity: from 20 to 1500 mm²/s (cSt)
NLGI 00, 000
Number of lubricant outlets 1 or 2 (front and/or bottom)
Outlet pressure max 38 bar max 552 psi
Feed volume
Oil
Liquid lubricant		 0.01 l/min
10 cm³/min
0.021 fluid ounces/min
0.61 in³/min
Operating temperature from +10 to +50 °C from +50 to +122 °F
Electric motor voltage 24 VDC
Protection class IP 54
Cartridge capacity 380 ml 12.8 fluid ounces
Capacity of a plastic tank 0.5; 1.0; 1.7 l 1.06; 2.1; 3.6 fluid ounces
Output connection M10×1 thread or SKF quick-release coupling 6–8 mm
Dimensions
without cartridge
with cartridge
with a fixed reservoir		 143×172×121 mm
307.5×172×121 mm
min. 240×239×210 mm
max. 240×439×210 mm
5.63×6.77×4.76 inches
12.1 x 6.77 x 4.76 inches
min. 9.45 x 9.40 x 8.27 inches
max 9.45×17.28×8.27 inches
Installation position vertical
Sample order
The product can be configured using a configuration code. The order template includes the applicable part number and an explanation.
ECP1-1WAA22-1F1000
  • Electric compact pump
  • Productivity 10 cm3/min
  • Working pressure 38 bar
  • With warning switch
  • With standard wall bracket
  • With electrical connector, square plug
  • With quick-release connector ∅6 mm, front
  • With quick-release connector ∅6 mm, at the bottom
  • Tank version
  • For liquid lubrication
  • 1.0 L tank
You can configure your product using the CAD configurator below. This will provide you with a specific order number.

Configure the product, download the CAD file

Related products